|
Audio System Symptom Troubleshooting - Multi-information display or touch screen does not dim or brighten with dimmer
Multi-information display or touch screen does not dim or brighten with dimmer
NOTE:
|
|
|
|
|
Check for B-CAN DTCs and resolve them before troubleshooting. |
|
|
Check the connectors for poor connections or loose terminals. |
|
1. |
Problem verification:
Problem verification
|
?1. |
Turn the ignition switch to ON (II), or press the engine start/stop button to select the ON mode. |
|
?2. |
Turn the combination light switch to the parking light position. |
|
?3. |
Rotate the dashlights brightness controller knob several times. | |
Does the multi-information display brightness change?
|
|
|
Intermittent failure, the system is OK at this time.? |
|
|
|
The failure is duplicated, go to step 2. |
|
|
|
The failure is duplicated, go to step 3. |
|
2. |
Open wire check (B CAN-H line, B CAN-L line):
Open wire check (B CAN-H line, B CAN-L line)
|
?1. |
Turn the combination light switch off. |
|
?2. |
Turn the ignition switch to LOCK (0), or press the engine start/stop button to select the OFF mode. |
|
?3. |
Disconnect the following connectors.
|
|
?4. |
Check for continuity between test points 1 and 2.
|
Test condition |
IG LOCK (0) or OFF mode |
| |
Audio unit connector A (24P): disconnected |
| |
Gauge control module connector A (32P): disconnected |
|
Test circuit |
B CAN-H |
|
Test point 1 |
Audio unit connector A (24P) No. 4 (PNK) |
|
Test point 2 |
Gauge control module connector A (32P) No. 30 (PNK) | |
|
|
Test circuit |
B CAN-L |
|
Test point 1 |
Audio unit connector A (24P) No. 2 (BLU) |
|
Test point 2 |
Gauge control module connector A (32P) No. 31 (BLU) | |
| | |
Is there continuity?
|
|
|
|
|
|
|
Repair an open in the wire(s) between the audio unit and the gauge control module.? |
|
3. |
Open wire check (B CAN-H line, B CAN-L line):
Open wire check (B CAN-H line, B CAN-L line)
|
?1. |
Turn the combination light switch off. |
|
?2. |
Press the engine start/stop button to select the OFF mode. |
|
?3. |
Disconnect the following connectors.
|
|
?4. |
Check for continuity between test points 1 and 2.
|
Test condition |
OFF mode |
| |
Audio-navigation unit connector A (24P): disconnected |
| |
Gauge control module connector A (32P): disconnected |
|
Test circuit |
B CAN-H |
|
Test point 1 |
Audio-navigation unit connector A (24P) No. 4 (PNK) |
|
Test point 2 |
Gauge control module connector A (32P) No. 30 (PNK) | |
|
|
Test circuit |
B CAN-L |
|
Test point 1 |
Audio-navigation unit connector A (24P) No. 2 (BLU) |
|
Test point 2 |
Gauge control module connector A (32P) No. 31 (BLU) | |
| | |
Is there continuity?
|
|
|
|
|
|
|
Repair an open in the wire(s) between the audio-navigation unit and the gauge control module.? | | 