DTC Troubleshooting: B0028-13

DTC B0028-13: Open or Increased Resistance in the Front Passenger's Side Airbag Inflator

Special Tools Required

?SRS Inflator Simulator 07SAZ-TB4011A

?SRS Simulator Lead L 070AZ-SNAA300

NOTE:

	Before doing this troubleshooting procedure, find out if the vehicle was in a collision. If so, verify that all the required components were replaced with new components of the correct part number, and that they were properly installed.
	Before doing this troubleshooting procedure, review SRS Precautions and Procedures, General Troubleshooting Information, and 12 Volt Battery Terminal Disconnection and Reconnection.
	Before replacing the SRS unit, check the SRS unit software version with the HDS. If the software version is not the latest, update the SRS unit software, and retest.

DTC Description	DTC
B0028-13 Open or increased resistance in the front passenger's side airbag inflator

Problem verification:

Problem verification

?1.	Clear the DTCs with the HDS.

?2.	Turn the vehicle to the ON mode, then wait for 10 seconds.

?3.

Check for DTCs with the HDS.

DTC Description	DTC
B0028-13 Open or increased resistance in the front passenger's side airbag inflator

Is DTC B0028-13 indicated?


	YES

The failure is duplicated. Go to step 2.


	NO

Intermittent failure, the system is OK at this time. Go to Troubleshooting Intermittent Failures. If another DTC is indicated, troubleshoot the DTC.?

Front passenger's side airbag inflator check:

Front passenger's side airbag inflator check

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.	Disconnect the negative cable from the 12 volt battery, then wait at least 3 minutes.

?3.	Disconnect the front passenger's side airbag inflator 2P connector (A) on the floor wire harness.

?4.	Connect the terminals of SRS simulator lead L to the SRS inflator simulator (2 ? connectors), then connect SRS simulator lead L to the front passenger's side airbag inflator 2P connector on the floor wire harness.

?5.	Reconnect the negative cable to the 12 volt battery.

?6.	Clear the DTCs with the HDS.

?7.	Turn the vehicle to the ON mode, then wait for 10 seconds.

?8.

Check for DTCs with the HDS.

DTC Description	DTC
B0028-13 Open or increased resistance in the front passenger's side airbag inflator

Is DTC B0028-13 indicated?


	YES

Go to step 3.


	NO

Open in the front passenger's side airbag inflator; replace the front passenger's side airbag, then clear the DTC.?

Open wire check (RSA?, RSA? lines):

Open wire check (RSA?, RSA? lines)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.	Disconnect the negative cable from the 12 volt battery, then wait at least 3 minutes.

?3.

Disconnect the following connector.

SRS unit connector B (39P)

?4.	Disconnect the SRS inflator simulator from SRS simulator lead L. Do not disconnect SRS simulator lead L from the front passenger's side airbag inflator 2P connector on the floor wire harness.

?5.

Measure the resistance of the test point.

Test condition	Vehicle OFF (LOCK) mode
	Front passenger's side airbag inflator 2P connector (on the floor wire harness): disconnected
	SRS unit connector B (39P): disconnected
	Front passenger's side airbag inflator 2P connector (on the floor wire harness): connected to SRS simulator lead L
Test point	SRS simulator lead L black terminal

Is there 1.0 ? or less?


	YES

The RSA? and RSA? wires are OK. Faulty SRS unit or poor connection at SRS unit connector B (39P) and the SRS unit. Check the connection; if the connection is OK, replace the SRS unit. If the DTC does not clear, replace the floor wire harness.?


	NO

Open in the floor wire harness; replace the floor wire harness, then clear the DTC.?