Road Departure Mitigation Symptom Troubleshooting - RDM indicator does not go off

1.

DTCs check:

DTCs check

?1.	Turn the vehicle to the ON mode.

?2.

Check for DTCs with the HDS.

DTC Description	DTC	Freeze Frame

Are any DTCs indicated?


	YES

Go to the indicated DTC's troubleshooting.?


	NO

Go to step 2.

2.

CAN gateway system DTC check:

CAN gateway system DTC check

?1.	Turn the vehicle to the ON mode.

?2.

Check for CAN gateway system DTCs with the HDS.

DTC Description	DTC
U0029-00 CAN Gateway F-CAN ch A Bus Off
U0047-00 CAN Gateway F-CAN ch B Bus Off
U3000-49 CAN Gateway Internal Failure

Is DTC U0029-00, U0047-00, or U3000-49 indicated?


	YES

Go to the troubleshooting for CAN gateway system DTC(s).?


	NO

Go to step 3.

3.

Fuse check 1:

Fuse check 1

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Check the following fuse.

Fuse

No. B29

Is the fuse OK?


	YES

The fuse is OK. Reinstall the fuse, then go to step 4.


	NO

Replace the fuse. Turn the vehicle to the ON mode, then the OFF (LOCK) mode. If the fuse blows again, repair the short to ground on the No. B29 fuse circuit.?

4.

Fuse check 2:

Fuse check 2

?1.

Check the following fuse.

Fuse

No. C39

Is the fuse OK?


	YES

The fuse is OK. Reinstall the fuse, then go to step 5.


	NO

Replace the fuse. Turn the vehicle to the ON mode, then the OFF (LOCK) mode. If the fuse blows again, repair the short to ground on the No. C39 fuse circuit.?

5.

Gauge control module operation check:

Gauge control module operation check

?1.	Turn the vehicle to the ON mode.

?2.	Check if all of the gauge indicators come on for a few seconds.

Do the indicator come on?


	YES

Go to step 6.


	NO

Go to the gauge control module self-diagnostic function.?

6.

Open wire check (IG1 OPTION line):

Open wire check (IG1 OPTION line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Disconnect the following connector.

Multipurpose camera unit 20P connector

?3.	Turn the vehicle to the ON mode.

?4.

Measure the voltage between test points 1 and 2.

Test condition	Vehicle ON mode
	Multipurpose camera unit 20P connector: disconnected
Test point 1	Multipurpose camera unit 20P connector No. 19
Test point 2	Body ground

Is there battery voltage?


	YES

Go to step 7.


	NO

Repair an open in the IG1 OPTION wire between the No. C39 fuse in the under-dash fuse/relay box and the multipurpose camera unit.?

7.

Open wire check (GND line):

Open wire check (GND line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Check for continuity between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	Multipurpose camera unit 20P connector: disconnected
Test point 1	Multipurpose camera unit 20P connector No. 14
Test point 2	Body ground

Is there continuity?


	YES

Go to step 8.


	NO

Repair an open in the GND wire between the multipurpose camera unit and body ground (G401), or repair poor ground (G401).?

8.

F-CAN circuit communication check:

F-CAN circuit communication check

?1.

Reconnect the following connector.

Multipurpose camera unit 20P connector

?2.	Turn the vehicle to the ON mode.

?3.	Select the FUNCTION TEST in the CAN gateway with the HDS, then select the F-CAN Bus Connected Unit Check.

Which result is indicated?


	Gauge control module (Bus A) is Not Available

Go to step 9.


	Multipurpose camera unit (Bus B) is Not Available

Go to step 10.


	Multipurpose camera unit and gauge control module are Detected

Intermittent failure, the system is OK at this time. Refer to intermittent failures troubleshooting. If the freeze data/on-board snapshot of this DTC is recorded, try to reproduce the failure under the same conditions with the freeze data/on-board snapshot.?

9.

Open wire check (F-CAN A_L line, F-CAN A_H line):

Open wire check (F-CAN A_L line, F-CAN A_H line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Disconnect the following connectors.

CAN gateway 16P connector

Gauge control module 32P connector

?3.

Check for continuity between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	CAN gateway 16P connector: disconnected
	Gauge control module 32P connector: disconnected
Test point 1	CAN gateway 16P connector (female terminals) No. 3:
Test point 2	Gauge control module 32P connector No. 21

Test point 1	CAN gateway 16P connector (female terminals) No. 11:
Test point 2	Gauge control module 32P connector No. 22

Is there continuity?


	YES

Check for loose terminals in the CAN gateway 16P connector and the gauge control module 32P connector. If they are OK, substitute a known-good gauge control module, then retest. If the indicators come on then go off after substitution, replace the original gauge control module.?


	NO

Repair an open in the F-CAN A_H wire or the F-CAN A_L wire between the gauge control module and the CAN gateway.?

10.

Open wire check (F-CAN B_H line, F-CAN B_L line):

Open wire check (F-CAN B_H line, F-CAN B_L line)

?1.	Turn the vehicle to the OFF (LOCK) mode.

?2.

Disconnect the following connectors.

CAN gateway 16P connector

Multipurpose camera unit 20P connector

?3.

Check for continuity between test points 1 and 2.

Test condition	Vehicle OFF (LOCK) mode
	CAN gateway 16P connector: disconnected
	Multipurpose camera unit 20P connector: disconnected
Test point 1	CAN gateway 16P connector (female terminals) No. 6:
Test point 2	Multipurpose camera unit 20P connector No. 2

Test point 1	CAN gateway 16P connector (female terminals) No. 14:
Test point 2	Multipurpose camera unit 20P connector No. 13

Is there continuity?


	YES

Check for poor connections or loose terminals at the CAN gateway and the multipurpose camera unit. Check for any authorized service information related to the DTCs or symptoms you are troubleshooting. If they are OK, replace the multipurpose camera unit.?


	NO

Repair an open in the F-CAN B_H wire or the F-CAN B_L wire between the multipurpose camera unit and the CAN gateway.?